天天中彩票官网

新闻动态
尼龙输送带跑偏的原因
尼龙输送带跑偏的原因
Reasons for deviation of nylon conveyor belt
在使用过程中,如果出现跑偏,则要作以下检查以确定原因,进行进行调整。输送带跑偏时常检查的部位和处理方法有:
In the course of use, if there is deviation, the following checks should be made to determine the reasons for the adjustment. The location and treatment methods of the belt deviation often include:
(1)检查托辊横向中心线与带式输送机纵向中心线的不重合度。如果不重合度值超过3mm,则应利用托辊组两侧的长形安装孔对其进行调整。具体方法是输送带偏向哪一侧,托辊组的哪一侧向输送带前进的方向前移,或另外一侧后移。
(1) check the non alignment degree between the center line of the idler roll and the longitudinal centerline of the belt conveyor. If the degree of overlap does not exceed 3mm, the long installation hole on both sides of the idler should be adjusted. The specific method is which side the conveyor belt deviates, which side of the roller group moves forward toward the conveyor belt, or the other side moves backwards.
(2)检查头、尾机架安装轴承座的两个平面的偏差值。若两平面的偏差大于1mm,则应对两平面调整在同一平面内。头部滚筒的调整方法是:若输送带向滚筒的右侧跑偏,则滚筒右侧的轴承座应当向前移动或左侧轴承座后移;若输送带向滚筒的左侧跑偏,则滚筒左侧的轴承座应当向前移动或右侧轴承座后移。尾部滚筒的调整方法与头部滚筒刚好相反。
(2) check the deviation of the two planes of the bearing housings on the head and tail rack. If the deviation of the two plane is greater than 1mm, the two plane should be adjusted in the same plane. Head drum adjustment method is: if the conveyor belt to the right side of the roller deviation, then the right side of the roller bearing seat should move forward or left bearing seat back; if the conveyor belt to the left side of the roller deviation, then the left side of the roller bearing seat should move forward or right bearing seat back. The tail roller adjustment method is just the opposite of the head drum.
(3)检查物料在输送带上的位置。物料在输送带横断面上不居中,将导致输送带跑偏。
(3) check the location of the material on the conveyor belt. The material is not centered in the cross section of the conveyor belt, which will lead to the deviation of the conveyor belt.
如果物料偏到右侧,则皮带向左侧跑偏,反之亦然。在使用时应尽可能的让物料居中。为减少或避免此类输送带跑偏可增加挡料板,改变物料的方向和位置。
If the material is on the right side, the belt deviates to the left side, and vice versa. When used, the material should be kept centered as far as possible. In order to reduce or avoid deviation of the conveyor belt, the baffle plate can be increased, and the direction and position of the material can be changed.

联系方式

  1. 名称:河北博傲橡胶制品有限公司
  2. 电话:15081233333
  3. 联系人:罗经理
  4. 地址:河北省保定市博野县橡胶工业园

版权 © 河北博傲橡胶制品有限公司 网址:www.1taxx.com  推荐:pvc输送带,尼龙输送带,矿用输送带,橡胶输送带生产厂家

全民彩彩票 周易彩票 国民投注 纵达彩票 天天中彩票app 周易彩票 天天中彩票 天天中彩票app下载 纵达彩票 全民彩彩票注册